Skip to content
Welland Plumbing and Drain

Plumbing repairs in Welland

Plumbing repairs in Welland

We repair leaks, running toilets, dripping faucets, split outdoor taps and old supply pipe. Before quoting, we find the source, name the pipe material and test the pressure. You see the price in writing first. If water is spraying now, shut the main valve and see emergency plumber.

Find the leak, name the pipe, test it, write the price, then fix it.

What happens when you call about a leak?

Start at the main shut-off. In most Welland houses it sits where the water service comes through the front basement wall, just before the meter. Turn it clockwise until it stops, then open the lowest cold tap to drain the lines. If water is near a light fitting, turn off that breaker. A pipe that is still spraying is an emergency call.

On the visit, the plumber finds the source before quoting. Water runs along joists and pipe, so the wet patch is often a metre or more from the fault. Once we have traced it, we identify the pipe and the fitting and write down the repair and its price. You approve it before any part is fitted. Work is performed by licensed plumbers (306A Certificate of Qualification).

Like-for-like repairs, such as a new faucet cartridge or a soldered coupling, are usually done during the visit. Replacing a run of pipe, adding a fixture or changing a drain can need a building permit under the Building Code Act, 1992. The City's building department decides whether a given job needs one. We note on the written price which applies.

How do we tell which pipe your house has?

We start at the service pipe, where it enters the house before the meter. Lead is dull grey and soft. A coin scratches it bright silver, a magnet will not stick, and the joint often has a bulge where it was wiped with solder. Galvanized steel is grey too, but a magnet sticks and the fittings are threaded. Copper scratches to a penny colour. Kitec is orange plastic for hot and blue for cold, with brass fittings.

Then we test the pressure. A gauge on the laundry or outdoor tap reads static pressure, the reading with every tap closed. Then we open taps and watch the needle. A steep drop under flow means the inside of the pipe is narrowed. Galvanized does this as rust builds on the inside wall. A main valve that is half seized gives the same symptom, so we check it as well. The low pressure guide explains the readings.

The street usually hints at the answer. French Town houses built before 1945 typically have a lead or galvanized service. The wartime houses on Dunkirk Road, Dieppe Street and Calais Street typically have galvanized or early copper. Karen Crescent and Aquador Drive, built in the 1960s and 1970s, typically have copper.

Why do pipes split in outside walls and at outdoor taps?

Water expands as it freezes. In a pipe with no room to expand, that splits copper or bursts a fitting. Environment Canada's 1981 to 2010 climate normals for the Welland station show about 139 days a year with a minimum at or below 0 °C and about 31 days below −10 °C. The pipes at risk run in outside walls, crawl spaces and unheated porches.

A split often stays hidden until it thaws, then shows as a spray. If a line is frozen but not yet leaking, close the main and warm the area gently. Never use an open flame on pipe in a wall.

The usual repair is to cut out the split section and replace it. We also look at why that run froze. Pipe can be moved off the outside wall or insulated. An outdoor tap can be changed to a frost-free type, which closes inside the heated wall, and given its own shut-off inside the basement. A hose left connected keeps water in a frost-free tap, and it splits anyway.

What does a pinhole leak in copper mean?

A pinhole is a small leak that pits through the copper wall from the inside. Look for a green crust, a fine spray or a drip at the low point of a horizontal run. It is common in copper of the age found around Fitch Street.

One pinhole is repaired with a short section and two couplings. Several in the same run mean the whole wall of that pipe is thinning. In that case we show you where the leaks are, price both the spot repair and replacing the run, and you choose.

Should old pipe be replaced: lead, galvanized or Kitec?

Lead service lines are replaced with new copper from the property line to the meter. In partnership with Niagara Region, the City of Welland offers a grant toward this to owners with a lead water service or one shared with a neighbour. The application must be approved before work begins, so apply first. Replacing the service means digging. A locate must be requested through Ontario Dig Authority before anyone digs. Public locates do not mark private lines.

Galvanized pipe does not recover once it has narrowed. Brown water after the taps have sat, low flow upstairs and leaks at threaded joints all mean the pipe is near the end. When the budget is split, replacing the worst runs first is a reasonable plan.

Kitec fails at its brass fittings. We check them for white or green build-up and give you the cost of replacing the system. Buyers often ask whether it is a deal breaker. See the Kitec and galvanized guide.

Why does a toilet run or a faucet drip?

A toilet that refills by itself has a flapper that no longer seals, or a fill valve set too high that spills into the overflow tube. Add a few drops of food colouring to the tank. If colour shows in the bowl within half an hour without a flush, the flapper is leaking. Water at the base of the toilet points to the wax ring or the flange, and the floor under it needs checking.

A faucet that drips from the spout needs a new cartridge or washer. Welland's water adds to the wear. Niagara Region published a hardness of 129 mg/L for the Welland Water Treatment Plant, measured Oct. 7, 2026. That means calcium and magnesium scale on aerators, cartridges and fill valves. We clean what can be cleaned and replace what has scaled shut. A slow drain is a different job, covered under drain cleaning.

Our commitments

What do we commit to on your job?

  • Licensed and insured

    Every plumber holds a current 306A Certificate of Qualification and is covered by liability insurance. Your home is protected on every job.

  • Every call is answered

    Day or night, a person or our receptionist answers, takes the details and a plumber calls you back.

  • Written price before work starts

    You see the number and approve it before any part is fitted. No surprises on the invoice.

  • 1-year workmanship warranty

    All labour comes backed by a one-year warranty. If a repair we made fails within the warranty period, we return and fix it at no additional labour cost.

Questions about repairs

When does a plumbing job in Welland need a building permit?

Under the Building Code Act, 1992, a permit from the municipality's chief building official is needed to install, extend, or materially alter or repair plumbing. New plumbing and changes to drains generally need one. The City of Welland's building department decides for a given job. The City's basement-flooding grant also requires a building permit and City inspections. Plumbing is a compulsory trade in Ontario, and the person doing it must appear on the Skilled Trades Ontario Public Register. Work is performed by licensed plumbers (306A Certificate of Qualification). Ask the building department before work starts, then see plumbing repairs.

All questions

Want the price before the work?

Tell us what the water is doing and how old the house is. You get a written price to approve before anything is fitted.