What should you do first when sewage comes up through the floor drain?
Stop running water. Every flush, shower and washer cycle in the house drains through the same main line. When that line is blocked or the street sewer is surcharged, the water comes out at the lowest opening. In most older Welland basements that opening is the floor drain.
Keep children and pets off the wet floor, because sewage carries bacteria. If water is reaching the furnace, the water heater or a power bar, switch off the basement circuits at the panel, but only if you can reach the panel from dry floor. Then call for an emergency plumber. Tell us whether it is raining heavily. Heavy rain points to the City sewer surcharging. A backup on a dry day points to a blockage in your own line.
How does a camera inspection find the fault?
The lateral is the pipe that carries everything from the house to the sewer main under the street. The camera goes in through a cleanout, which is a capped opening on the main drain, usually at the base of the stack or at the front foundation wall. If the house has no cleanout, the toilet can be lifted and the camera sent in through the flange.
The camera head rides on a semi-rigid push rod. It carries a sonde, a small radio transmitter. A receiver held above ground picks up the sonde and marks the spot and depth of anything the camera sees. If a repair is needed, the digging starts at that mark instead of with a trench the length of the yard.
The footage shows the pipe material, where it changes, and the condition of each joint. It shows roots pushing through, offset joints, cracks, a sag that holds standing water, or a section that has collapsed. If a blockage stops the camera, the line is cleared first with drain cleaning and the camera goes back in. You watch the recording with the technician.
What does a sewer repair involve, and what do you decide?
There are two options. A spot repair opens the ground at the sonde mark, cuts out the broken clay or cast iron and replaces it with ABS. ABS is the black plastic drain pipe used in current construction. It is joined to the old pipe with shielded rubber couplings. A full replacement runs new ABS for the length of the lateral. A spot repair suits a pipe that is sound apart from one fault. If there are roots at joint after joint, or a long sag, the next joint is likely to fail too, and replacement is the repair that lasts.
Before any digging, a locate is requested through Ontario Dig Authority (formerly Ontario One Call), as the Ontario Underground Infrastructure Notification System Act, 2012 requires. Public locates mark utility lines. They do not mark private lines such as your own sewer, and that is why the sonde mark matters. Under the Building Code Act, 1992, repairing or altering drains generally needs a building permit. The City of Welland building department confirms whether a given job does.
You get a written price for each option before work starts, and you choose which one to do. Work is performed by licensed plumbers (306A Certificate of Qualification).
How is a backwater valve installed, and how does the City grant work?
A backwater valve is a check valve set in the main building drain. Its flap stays open for normal flow out of the house and closes when sewage pushes back from the street. Ontario's Building Code, Part 7, Article 7.4.6.4., requires one in new construction in two cases: where fixtures sit below the level of the street, and where they sit below the upstream sanitary manhole cover in a house served by a public sewer. A house built without a valve can have one fitted.
To install one, the plumber cuts the basement floor over the main drain, breaks out the concrete and cuts into the cast iron or clay. The valve is set level in the line with an access cover at floor height, so the flap can be inspected and cleaned. The floor is then filled and re-poured. When the valve is closed, water from the house cannot leave either. During a street backup, don't use the fixtures upstairs.
The City of Welland offers homeowners a grant toward protection from basement flooding. It covers a backwater valve. It also covers disconnecting foundation drains and downspouts from the sanitary system and installing a new sump pit and pump. The City requires two contractor quotations, a building permit and City inspections. Read the City's application steps before you book the work, so the quotations, permit and inspections happen in the order the City asks for. A written quotation from Welland Plumbing and Drain can serve as one of the two.
What signs point to a failing sewer line in a Welland house?
Watch for a toilet that gurgles when the washer empties, a floor drain that gets wet after someone showers upstairs, or slow drains on the lowest level only. Other signs are a sewer smell in the basement, a strip of lawn that sinks or stays greener over the line, and a blockage that comes back at about the same time each year. A blockage that returns like that is usually roots.
The faults follow the age of the house. French Town, around Empire, Burgar, Cozy and Division streets, was built before 1945. Those houses typically have cast iron stacks running to a clay tile sewer and a floor drain tied straight to the sewer with no sump. Root-blocked or collapsed clay laterals and sewage backing up through the floor drain are the usual calls there. The 1940s wartime houses on Dunkirk Road, Dieppe, Corvette and Calais streets and McNaughton Road typically have cast iron drains and a clay lateral, so the usual faults are cast iron rusted through and clay joints filled with roots.
On Karen Crescent and Aquador Drive by Fitch Street, built in the 1960s and 1970s, drains are typically cast iron or early ABS, the lateral is clay or early plastic, and the weeping tile was often connected to the sanitary sewer. Roots in the original lateral and backups in heavy rain are the usual problems. These are typical for each era. The camera confirms what your house actually has.
Why do backups come on the heaviest rain days?
Environment Canada's 1981 to 2010 climate normals for the Welland station record about 856 mm of rain a year, with five to six days a year of 25 mm or more. Backups cluster on those days. Weeping tile is the perforated pipe around the footing that collects groundwater. When it is tied to the sanitary sewer, every connected house sends groundwater into a pipe meant for sewage. The sewer surcharges, and the water rises to the lowest opening it can reach.
A backwater valve stops the street sewer from coming into the house. It does nothing about your own weeping tile. If the tile still drains into the sanitary line upstream of the valve, a closed valve leaves that water nowhere to go except the floor drain. The valve and the disconnection work as a pair, and the City's grant covers both. See sump pumps for sizing the pit and pump, the discharge and battery backup.
