Skip to content
Welland Plumbing and Drain

Water heaters in Welland

Water heater repair and installation in Welland

Is the tank leaking at the base, or is the hot water gone, rusty or lukewarm? Welland Plumbing and Drain repairs, replaces and installs tank and tankless water heaters, electric and gas. We test the elements, controls and venting first, then give you a written price. To weigh tank against tankless, read the guide.

Tank or tankless, electric or gas: tested first and priced in writing.

What should you do if the tank is leaking or there is no hot water?

Close the cold-water shut-off on the pipe that enters the top of the tank. This stops the tank from refilling. On an electric heater, also switch off its breaker at the panel, because an element that heats with no water around it burns out quickly. On a gas heater, turn the control knob to pilot or off. If you smell gas, leave the house and call the gas utility's emergency line from outside.

Water at the base can come from the tank or from something above it. Common sources are the drain valve, a fitting on the supply line, or the temperature and pressure relief valve. That is the valve on the side or top of the tank, with a pipe that runs down toward the floor. We dry the area and trace the water back to where it starts. A leaking fitting or valve can be repaired. A leaking steel tank cannot, because it means the glass lining inside has failed, so the tank has to be replaced. If water is spreading across the floor, treat it as an emergency call.

How is a water heater tested before anything is replaced?

An electric tank has two heating elements, each with its own thermostat. With the power off, we measure the resistance of each element with a meter. An open reading means the element has burned out. With the power on, we check that each thermostat passes voltage when it should. If the bottom element fails, the water stays lukewarm. If the top one fails, there is little or no hot water at all.

On a gas tank, we check the pilot, the burner and the thermocouple. The thermocouple is a sensor that proves the pilot is lit and holds the gas valve open. We also check the vent for draft, to make sure combustion gases go up the flue and do not spill into the room. On a tankless unit, we read the fault code, clean the inlet filter screen, check the flow sensor and look for scale in the heat exchanger.

Each reading points to a specific failed part. You can then replace that part or replace the heater, with both prices in writing.

How is a replacement sized and installed?

A tank is sized by its first-hour rating as well as its volume in litres. The first-hour rating is how much hot water a full tank can deliver in its first hour of use. We work it out from the number of bathrooms, the showers that run back to back, and any large tub. A tankless unit is sized by its flow rate in litres per minute at the temperature rise it has to supply. Welland's supply comes from Lake Erie, and the incoming water is colder in January, so a unit that runs two showers in summer may only manage one in winter. An electric tankless unit also needs a large electrical supply, which many older panels cannot provide. The guide covers that trade-off in more detail.

A standard installation includes a new shut-off valve, the relief valve and its discharge pipe, and the supply connections. If the house has a check valve or backflow preventer on the main, heated water has nowhere to expand and pressure builds in the system. In that case we fit an expansion tank. Under the Building Code Act, 1992, installing or altering plumbing generally needs a building permit. The City's building department decides whether your replacement does, and you will know before work starts.

Work is performed by licensed plumbers (306A Certificate of Qualification). Gas work is performed by TSSA-certified gas technicians, as Ontario Regulation 212/01 (Gaseous Fuels) requires for fuel-fired appliances such as gas water heaters.

Why is there a 49 °C limit at the tub and shower?

Ontario's Building Code (Part 7, Article 7.2.10.7., Water Temperature Control) limits water coming from a shower head or into a bathtub to 49 °C. Hotter water scalds skin fast, especially on children and older adults.

The tank is often set hotter than that. To meet the limit, a temperature-control valve blends hot water with cold so the outlet stays at or below 49 °C. This can be a mixing valve at the heater or a pressure-balancing valve in the shower. After an installation, we measure the temperature at the tub spout with a thermometer and adjust the valve until it reads within the limit. If your tub runs hotter than that, the valve needs adjusting or replacing.

Which signs mean the heater is failing?

Rusty water from the hot tap only points to the inside of the tank: either the anode rod has worn away or the tank wall is corroding. The anode rod is a metal rod that corrodes in place of the steel tank. Rumbling or popping while the burner or elements run means sediment has built up on the bottom. A pilot that will not stay lit usually means the thermocouple has failed. A relief valve that drips points to high pressure, high temperature or a worn valve, and we test which one it is.

Read the rating plate on the side of the tank. The serial number usually includes the year it was made. Check the manufacturer's warranty terms before you decide anything. The tank and the parts are often covered for different periods, and some manufacturers require proof of the installation date. A tank near the end of its tank warranty that needs a costly part is usually a replacement decision. A newer tank with one failed element is usually a repair.

What does Welland's water do to a water heater?

Welland's water is treated at the Welland Water Treatment Plant, which Niagara Region operates and which also serves Pelham and parts of Thorold. The Region's published hardness for that plant was 129 mg/L, measured Oct. 7, 2026. Hardness is the dissolved calcium and magnesium in the water. At 129 mg/L, the water is hard enough to leave scale when heated.

In a tank, scale and sediment settle on the bottom. On a gas tank, they insulate the bottom from the burner, which wastes fuel and overheats the steel. On an electric tank, they build up on the lower element until it fails. Flushing the tank through its drain valve removes loose sediment. In a tankless unit, scale lines the heat exchanger and cuts the flow, and flushing it with a descaling solution through its service valves restores the flow. How often to flush depends on how much hot water the household uses; the scale on the old element or in the filter screen is the best guide.

Our commitments

What do we commit to on your job?

  • Licensed and insured

    Every plumber holds a current 306A Certificate of Qualification and is covered by liability insurance. Your home is protected on every job.

  • Every call is answered

    Day or night, a person or our receptionist answers, takes the details and a plumber calls you back.

  • Written price before work starts

    You see the number and approve it before any part is fitted. No surprises on the invoice.

  • 1-year workmanship warranty

    All labour comes backed by a one-year warranty. If a repair we made fails within the warranty period, we return and fix it at no additional labour cost.

Questions about water heaters

Where does Welland's water come from, and how hard is it?

The Welland Water Treatment Plant takes its raw water from Lake Erie by way of the Welland Canal and the Welland Recreational Canal, which is the old Welland Canal. Niagara Region operates the plant. It also serves Pelham and portions of Thorold. The Region's published hardness for the plant was 129 mg/L, measured Oct. 7, 2026. Hardness is dissolved calcium and magnesium. When water is heated, those minerals settle as scale in the tank and on heating elements. If your tank crackles or rumbles as it heats, read water heaters.

Who may install a gas water heater in Welland, and how hot should the water be?

Under Ontario Regulation 212/01, a gas water heater must be installed and serviced by a contractor registered with the Technical Standards and Safety Authority. Gas work is performed by TSSA-certified gas technicians. Hot water has its own limit. Article 7.2.10.7. of Ontario's Building Code caps water from a shower head or into a bathtub at 49 °C. A tank set hotter than that is tempered with a mixing valve before the water reaches the tub. Measure the water at the tub with a kitchen thermometer. If it reads above 49 °C, see water heaters.

All questions

Want the price before the work?

Tell us what the water is doing and how old the house is. You get a written price to approve before anything is fitted.