Skip to content
Welland Plumbing and Drain

FAQ

Frequently asked questions

If your question is not here, ask us directly.

A plumber explaining an answer to a homeowner beside the kitchen sink

Drains and sewers

How do you know if your house has a backwater valve?

A backwater valve is a flap in the main building drain. It closes when the City sewer surcharges and sewage tries to flow back into the house. To check for one, look at the basement floor near the front wall, where the drain leaves the house, for a removable cover or an access box. Many Welland houses have no valve, from French Town to the wartime streets off Dunkirk Road. Their floor drain runs straight to the sewer. The City of Welland's basement-flooding grant covers a valve if you get two contractor quotations, a building permit and City inspections. If there is no cover, ask for a camera check through sewer repair and backwater valves.

Why is drain cleaning so expensive?

The cost depends mostly on which line is blocked. A sink trap is cleared at the fixture. A main line needs a cleanout, which is a capped access fitting on the drain. It also needs a powered cable sized to the pipe, and often a camera to see what the cable hit. In Welland's older houses the main line runs to a clay lateral, the pipe under the lawn. If roots have grown in at its joints, the work means cutting them and then judging whether the pipe will hold. A buried cleanout adds time. You see the price in writing before work starts. List which drains are slow, then see drain cleaning.

Why do Welland basements back up during heavy rain?

Environment Canada's 1981 to 2010 climate normals for the Welland station record about 856 mm of rain a year, with five to six days of 25 mm or more. On those days the sanitary sewer fills. In the Karen Crescent and Aquador Drive subdivisions, foundation weeping tile was often connected to that sewer, so groundwater adds to the load. In older houses the basement floor drain is the lowest opening on the system, and sewage comes up there first. The fix is a backwater valve. Where weeping tile is tied into the sewer, it also means disconnecting the tile and running it to a sump pump. Note which drain overflowed and on what day, then see sewer repair and backwater valves.

What sets the cost of installing a sump pump in Welland?

Four things set the cost: whether a pit already exists, how much weeping tile has to be rerouted, where the discharge can go, and whether you add a battery backup for rain days. In a Welland house whose weeping tile drains to the sanitary sewer, the tile has to be cut off from the sewer. A new pit is then dug into the floor, and the pump is sized to the inflow. The City of Welland's basement-flooding grant covers disconnecting foundation drains and downspouts and installing a pit and pump. It requires two quotations, a building permit and City inspections. Get both quotations in writing, then read sump pumps.

Water and water heaters

Where does Welland's water come from, and how hard is it?

The Welland Water Treatment Plant takes its raw water from Lake Erie by way of the Welland Canal and the Welland Recreational Canal, which is the old Welland Canal. Niagara Region operates the plant. It also serves Pelham and portions of Thorold. The Region's published hardness for the plant was 129 mg/L, measured Oct. 7, 2026. Hardness is dissolved calcium and magnesium. When water is heated, those minerals settle as scale in the tank and on heating elements. If your tank crackles or rumbles as it heats, read water heaters.

Does my older Welland house still have a lead water service?

In French Town, around Empire, Burgar and Cozy streets, older houses typically have a lead or galvanized steel service. Look at the pipe where it enters the basement, before the meter. Lead is dull grey, scratches bright silver with a key, and a magnet will not stick to it. Galvanized steel holds a magnet. Ontario's standard for lead in drinking water is 0.010 mg/L, under Ontario Regulation 169/03. The City of Welland and Niagara Region offer a grant toward replacing a lead service with new copper. The application must be approved before work begins. Apply first, then book plumbing repairs.

Why is the water pressure low in an older Welland house?

Galvanized steel corrodes from the inside. Rust and scale narrow the bore until flow drops, and the drop is worst at the fixtures furthest from the service. That pipe is typical in French Town and on the wartime streets off Dunkirk Road. A corroded service from the street restricts flow the same way before the water reaches the house. To test, open the cold tap nearest the meter and one upstairs. If the tap downstairs is strong and the one upstairs is weak, the house piping is the problem. If both are weak, the service or the main shut-off is. Run that check, then read Why did the water just turn off, and why is the pressure low?

Is Kitec plumbing still used?

No. Kitec is a plastic and aluminium composite pipe with brass fittings, usually orange for hot and blue for cold. The brass fittings corrode and can fail without warning. It is no longer installed, but some houses still have it behind the walls. To check, look at the pipes at the water heater and under the sinks. The guide covers whether to replace it and whether it should stop a purchase: Kitec and galvanized pipe: should you replace it, and is it a deal breaker when buying a house?

Emergencies and safety

Why do pipes freeze in Welland houses, and what should I check first?

Environment Canada's 1981 to 2010 climate normals for the Welland station show about 139 days a year with a minimum at or below 0 °C, and about 31 days below −10 °C. Pipes freeze where that cold reaches them: supply lines in outside walls, crawl spaces, unheated porches and the line to an outdoor tap. Ice expands and splits the pipe, and the leak often shows only after the thaw. If a tap gives no water on a cold morning, close the main shut-off where the service enters the basement before you warm anything, then book an emergency plumber.

Who may install a gas water heater in Welland, and how hot should the water be?

Under Ontario Regulation 212/01, a gas water heater must be installed and serviced by a contractor registered with the Technical Standards and Safety Authority. Gas work is performed by TSSA-certified gas technicians. Hot water has its own limit. Article 7.2.10.7. of Ontario's Building Code caps water from a shower head or into a bathtub at 49 °C. A tank set hotter than that is tempered with a mixing valve before the water reaches the tub. Measure the water at the tub with a kitchen thermometer. If it reads above 49 °C, see water heaters.

Do I need a locate before my sewer lateral is dug up?

Yes. In Ontario, a locate must be requested through Ontario Dig Authority, formerly Ontario One Call, before any digging. This is required by the Ontario Underground Infrastructure Notification System Act, 2012. Public locates mark buried utility lines, but not private lines such as your own sewer lateral. On Welland's older streets that lateral is often clay pipe under the front lawn. Running a camera down the lateral shows its route and depth before anyone digs. Request the locate early, and book the camera through sewer repair and backwater valves.

General

When does a plumbing job in Welland need a building permit?

Under the Building Code Act, 1992, a permit from the municipality's chief building official is needed to install, extend, or materially alter or repair plumbing. New plumbing and changes to drains generally need one. The City of Welland's building department decides for a given job. The City's basement-flooding grant also requires a building permit and City inspections. Plumbing is a compulsory trade in Ontario, and the person doing it must appear on the Skilled Trades Ontario Public Register. Work is performed by licensed plumbers (306A Certificate of Qualification). Ask the building department before work starts, then see plumbing repairs.

Still have a question?