Skip to content
Welland Plumbing and Drain

Sump pumps in Welland

Sump pump installation and repair in Welland

A sump pump keeps groundwater from the weeping tile out of the basement and out of the sewer. Welland Plumbing and Drain installs new pits and pumps when foundation drains come off the sanitary line, repairs and replaces failed pumps, and adds battery backup for storms. For the sewer side, see backwater valves.

A new pit when the weeping tile comes off the sewer, and a pump that keeps running when the power goes.

What happens when the pump has stopped and the pit is filling?

Start with the power. Most sump pumps plug into a GFCI outlet. That is a ground fault receptacle that cuts power when it senses current leaking to ground, and a damp basement trips it easily. Press reset. If it trips again, leave it off and keep out of the water. If the pump has power but does not start, lift the float gently with a dry stick. If the pump runs when the float is lifted, the switch is stuck or tangled and the motor is fine.

On the visit, the plumber checks the same chain in order: supply, float switch, motor, impeller and check valve. The check valve is the one-way valve in the discharge pipe above the pump. When it fails, the water in the pipe falls back into the pit every time the pump stops, so the pump cycles far more often than it should. If the motor has failed, the fix is a replacement pump in the existing pit. You get the written price before it is fitted.

If water is over the floor and the floor drain is backing up as well, the problem may be the sewer, not the pump. See emergency plumber for what to shut off first.

How is a new pit and pump put in when the weeping tile comes off the sewer?

Weeping tile is the perforated pipe laid around the footings to collect groundwater. In the 1960s and 1970s houses around Karen Crescent, Aquador Drive and Fitch Street, it was often connected to the sanitary sewer. In French Town and the wartime streets off Dunkirk Road, many basements have only a floor drain to the sewer and no sump at all. Either way, on a heavy rain day groundwater runs into the pipe that carries the sewage, and the sewer runs out of room for both.

Disconnecting the tile means cutting the basement slab, digging a pit near where the tile meets the sewer connection, setting a pit liner, turning the tile into the pit and sealing the old connection to the sanitary line. The pump then lifts the groundwater out through its own discharge pipe. A camera inspection of the lateral comes first. It shows where the tile joins and whether the clay or cast iron at that joint is sound.

The City of Welland offers a basement flooding grant. One part covers disconnecting foundation drains and downspouts from the sanitary system and installing a sump pit with pump. A separate part covers a backwater valve. The conditions require two contractor quotations, a building permit and City inspections. Many owners do the valve in the same project. Work is performed by licensed plumbers (306A Certificate of Qualification).

How is the pump sized, and where does the water go?

Sizing starts with two numbers. The first is inflow: how fast the pit fills on a wet day, measured by timing the rise between pump cycles. The second is total head, which is the vertical lift from the pit to the outlet plus the friction of the pipe run and fittings. A pump moves less water as head rises, so it is chosen from its performance curve at your head, not from the largest figure printed on the box.

The discharge goes outside, onto ground that slopes away from the foundation. It never goes back into the sanitary sewer. Environment Canada's 1981 to 2010 normals for the Welland station give about 139 days a year at or below 0 °C and about 31 days below −10 °C. A discharge line with a low spot holds water, and that water freezes solid in January. The pump then runs against a blocked pipe. For that reason the outside run is sloped so it drains fully between cycles.

If a discharge line is to be buried, a locate is requested through Ontario Dig Authority before anyone digs. Public locates do not mark private lines such as your own sewer lateral, so those are traced separately.

Why add a battery backup?

The same Environment Canada normals record about 856 mm of rain a year at the Welland station, with five to six days of 25 mm or more. The sump works hardest on those days, and the storms that bring them also cut the power, which leaves a primary pump doing nothing.

A battery backup is a second pump in the same pit, set slightly higher than the first. It has its own float switch and check valve, and it runs from a deep-cycle battery kept topped up by a charger. It starts only if the water rises past the primary pump's level, and it sounds an alarm when it does. Run time depends on the battery's capacity and how often the pump cycles. The battery is sized to the measured inflow, not to an advertised figure.

Batteries wear out on their own schedule, so follow the manufacturer's replacement interval. To test the backup, unplug the primary pump and fill the pit with a bucket.

What are the signs a sump pump is failing?

If the pump runs without stopping in dry weather, the float is usually stuck or the check valve has failed. If it hums but moves no water, the impeller is jammed or the motor is failing. Short cycling means the pump starts and stops every few seconds. It points to a float set too tight or water falling back down the discharge pipe.

Other signs to look for are rattling or grinding, which means debris in the impeller or worn bearings; a pump that starts only when you lift the float by hand; water seeping up around the outside of the pit liner; and rust on the discharge pipe just above the pump. A sewage smell at the pit means the old sanitary connection is not fully sealed or a nearby floor drain trap has dried out.

Which faults are repaired, and which mean a new pump?

The float switch, check valve and discharge pipe are parts, and replacing them is a repair. A burned-out motor or a cracked pump housing is not repaired; the pump is replaced. A cracked pit liner, or a pit too shallow for the float to travel, is rebuilt, because a new pump in a bad pit fails the same way the old one did.

When a pump is replaced, the plumber measures inflow and head again rather than copying the old label. If the old pump ran constantly, it may have been too small, or the weeping tile may be carrying more water than it should. The plumber tells you which it is. You decide whether to replace like for like or change the setup.

Our commitments

What do we commit to on your job?

  • Licensed and insured

    Every plumber holds a current 306A Certificate of Qualification and is covered by liability insurance. Your home is protected on every job.

  • Every call is answered

    Day or night, a person or our receptionist answers, takes the details and a plumber calls you back.

  • Written price before work starts

    You see the number and approve it before any part is fitted. No surprises on the invoice.

  • 1-year workmanship warranty

    All labour comes backed by a one-year warranty. If a repair we made fails within the warranty period, we return and fix it at no additional labour cost.

Questions about sump pumps

What sets the cost of installing a sump pump in Welland?

Four things set the cost: whether a pit already exists, how much weeping tile has to be rerouted, where the discharge can go, and whether you add a battery backup for rain days. In a Welland house whose weeping tile drains to the sanitary sewer, the tile has to be cut off from the sewer. A new pit is then dug into the floor, and the pump is sized to the inflow. The City of Welland's basement-flooding grant covers disconnecting foundation drains and downspouts and installing a pit and pump. It requires two quotations, a building permit and City inspections. Get both quotations in writing, then read sump pumps.

All questions

Want the price before the work?

Tell us what the water is doing and how old the house is. You get a written price to approve before anything is fitted.